Concrobium is perfectly suitable for use in a fogger machine. A fogger machine is advantageous in many ways. For instance, you’ll get a diffuse application that evenly coats every surface, especially in an enclosed environment.
Fogger machines are typically used for parties and Halloween-type events. The fog machine effects make it a perfect disbursement method for concrobium or other mold-killing agents.
Will It Kill Any Mold In A Fogger Machine?
The three chemical compounds in concrobium destroy mold down to its roots. Not only will concrobium kill any mold in a fogger machine, but it will also leave behind a preventative against future mold growth.
Also, since fogger machines are typically made of aluminum, stainless steel, or plastic, mold can’t gain a long-term foothold by taking root beneath a porous surface. Once the concrobium kills it, mold will have difficulty taking root again.
What’s The Active Ingredient In Concrobium
The active ingredient in concrobium is Sodium Carbonate, however, there are two other ingredients as well, Sodium Bicarbonate and Trisodium Phosphate.
These three ingredients combine to eliminate every last vestige of mold that it encounters. They also leave behind a residue that, for a time, acts as an effective deterrent to future mold growth.
If you have mold growing inside a fogger machine, concrobium will wipe it out. Mold Control Panama terms it as a tri-salt polymer, which is an apt statement because of both its alkaline level and how it bonds to surfaces for a time, deterring any mold from regaining a foothold.
How Does It Kill Mold?
When particles of concrobium settle on top of the mold, it begins to dry. As the concrobium dries, it strangles the mold from the roots upward, killing it. Also, concrobium leaves behind a layer of antimicrobial residue that works as a preventative.
The single, active ingredient and the three combined ingredients act similarly to baking soda, which has led to accusations that concrobium is nothing more than water with a mixture of baking soda.
Nothing could be farther from the truth. Baking Soda only has a single ingredient, and that is Sodium Bicarbonate. Alone, it is nowhere near as effective in killing mold as the Sodium Carbonate, Sodium Bicarbonate, and Trisodium Phosphate found in concrobium.
Will It Hurt The Parts Of A Fogger Machine?
Concrobium has no known detrimental effects as far as the parts of a fogger machine are concerned. Concrobium has a pH balance that is above 11 on a scale of acidic to alkaline levels. Anything above 6.5 is considered to be alkaline, rather than acidic.
If it were acidic, there might be cause for concern with long-term damage to fogger machines. Still, a fogger machine should be cleaned out appropriately after each use.
It may even be beneficial to clean it and run it with warm water to help clean the small parts that atomize the liquid.
Most concrobium websites, such as mold-advisor and concrobium, strongly advise the use of fogger machines with concrobium. You get all of the benefits of concrobium’s mold-killing formula, without worrying about any damage to the fogger machine.
If it makes a difference to you, however, you can always clean it out when the job is done by systematically clearing all of the concrobium out of the machine.
Will It Make The Fogger Machine Dangerous To Use Later?
It won’t be dangerous later down the road if you clean it properly. When using concrobium in a fogger machine, be sure to open the machine and remove the suction tube from the remaining liquid and then continue to run the machine. This will atomize the remaining liquid within the internal tubes.
After the machine dispenses what’s in the tubes, dump the remaining liquid from the reservoir, clean it and run hot or warm water through the machine several times. Stage Bibles recommends using white vinegar, but only after the machine has been thoroughly cleaned and emptied.
What Do You Normally Use To Remove Mold In A Fogger Machine?
A 50/50 solution of water and white vinegar. White vinegar is very effective at eliminating mold thanks to its antimicrobial and antibacterial properties.
Like concrobium, vinegar also serves as a mold preventative, though the acetic acid that is the primary ingredient in vinegar doesn’t last as long. Mixed with baking soda and hydrogen peroxide, vinegar is even more effective as a mold-killing agent and as a preventative.
Alone, white vinegar will clean almost anything. Not only do people consume it, but they also use it to clean floors, spray tiles in bathrooms, wipe down mirrors, and spray in the corners under sinks. It’s an effective mold killer and an insect deterrent as well, all while making a good salad dressing.
How Do You Prevent Mold In A Fogger Machine?
First and foremost, keep it dry and store it in a cool location. A fogger machine is no different than any other surface when it comes to mold. If it’s warm and humid, mold has an opportunity to take root.
Each time you’re finished with it, be sure to adequately clean it out and consider running a solution of vinegar and water through it. Fogger machines aren’t too complicated. If you’re familiar with cleaning paint lines, the concepts are the same.
The most important parts are the ones you cannot see, such as the interior tubes and atomizers. That’s why it’s good to run anti-mold solutions through it from time to time.
How Do You Clean And Maintain A Fogger Machine So It Doesn’t Get Moldy?
The most important thing is to make sure that it’s dry before storing it. After each use, be sure to clear all of the tubes and the reservoir. Run a 50/50 solution of water and vinegar through it and be sure to hand dry as much as you can when it’s complete.
If you own a dehumidifier, consider storing the fogger machine near it as it runs. Otherwise, be sure to keep it dry and store it in a dry environment where it stays cool. Inside the house, don’t store it near water heaters, washing machines, under sinks, or near a dishwasher.